Compaq AlphaServer GS60 Guide d'installation

GS60/8200 to GS60EUpgrade ManualOrder Number: EK–GS60E–UP. A01Use this manual as a quick reference to upgrade an AlphaServerGS60 or AlphaServer 8200 t

4 Upgrade ManualNOTE: AC power receptacles are also required for console terminals and printers.Figure 1 AC Power ReceptaclesGS60E24-99GNDVVVPHAS

Procedure 53 Check All Materials and Position the New CabinetUnpack and position the new cabinet. Review what needs to be moved from theold cabine

6 Upgrade Manual Figure 2 System Cabinet, Front View(Front View)OM22-99 CD Drive(and optional floppy drive)BlowersDWLPB PCIPower SuppliesAC Input

Procedure 7Already installed in the new cabinet are the following:• TLSB card cage• CD-ROM drive• Operator control panel• CCL panel• One StorageWork

8 Upgrade Manual4 Power Down the GS60 or 8200 SystemTurn off power to the existing system.Figure 3 System Circuit Breakers (shown with redundant

Procedure 91. With the system in console mode, depress the pushbutton on the control panel tothe Off position (out).2. Open the rear door of the cab

10 Upgrade Manual5 Remove the Modules from the GS60/8200 TLSB Card CagePut on an antistatic wrist strap, remove all TLSB modules, and place th

Procedure 11Tools required: small and large flathead screwdrivers1. Ground yourself to the cabinet with the antistatic wrist strap.2. Remove each pr

12 Upgrade Manual6 Insert the Modules in the GS60E TLSB Card CageDetermine the placement of the modules in the TLSB card cage. Inspect theKN7CG mo

Procedure 13Tools required: small flathead screwdriver1. Before installing the modules, determine their placement:a. Processor modules start at slot

First Printing, August 1999The information in this publication is subject to change without notice.COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR

14 Upgrade Manual7 Move Devices from the Storage Drawer From the front move the disk or tape drive and the StorageWorks power supply,and from the

Procedure 15Remove the storage device from the front of the storage drawer and the powersupply. Remove any devices from the rear of the drawer. In

16 Upgrade Manual8 Move PCI Modules from the PCI ShelvesSlide out one PCI shelf at a time and remove modules for transfer to the newcabinet.Figure

Procedure 17adapters the hose number connections remain the same. (Remember that youlabeled the hoses when removing them from the KFTHAs.)2. Remove

18 Upgrade Manual9 Move StorageWorks DevicesRemove StorageWorks power supplies, devices, and DWZZA/Bs from theStorageWorks shelves in the old cabi

Procedure 19To remove SCSI devices from StorageWorks shelves:1. Disconnect the input power cord from the power supply. See ➊ in Figure 10.2. Unplug

20 Upgrade Manual10 Power Up and Verify the SystemTurn on the system, run console diagnostics, and issue the test command. Checkthe system configur

Procedure 211. Plug in the AC power cord.2. Set the main AC circuit breaker to the on position.3. Push the control panel On/Off button to on.4. To v

Index-1IndexAAC input box, 6AC input voltages, 3AC power receptacles, 4BBA36R-RC, 19Blowers, 6CCabinet, front view, 6Cabling, 11CD-ROM, 6Checking mate

iiiContentsPreface...vProcedure1 Overvi

ivTables1 AlphaServer 8200/GS60/GS60E Documentation ...vi2 Three-Phase AC Input Voltages...

vPrefaceIntended AudienceThis manual is written for the customer service engineer.Document StructureThis manual uses a structured documentation design

viTable 1 AlphaServer 8200/GS60/GS60E DocumentationTitle Order NumberHardware User Information and InstallationGS60E Operations Manual EK–GS60E–OPGS

Procedure 1Procedure1 OverviewFollowing are the steps to upgrade an AlphaServer GS60 or 8200 to an AlphaServerGS60E:1. Prepare the site.2. Check al

2 Upgrade Manual2 Prepare the SiteGet a hard copy of the 8200/GS60 system configuration, note any additionaloptions you may be adding with this upg

Procedure 3Shut down the operating system and issue the console commands show configuration,show device, and show <envar> to show the system c