Compaq AlphaServer ES40 Spécifications Page 204
- Page / 240
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7-14 Compaq AlphaServer ES40 User’s Guide
7.4.3 Test Command
The test command verifies all the devices in the system. This command
can be used on all supported operating systems.
Example 7–4 Test Command
P00>>> test
Testing the Memory
Testing the DK* Disks(read only)
No DU* Disks available for testing
No DR* Disks available for testing
Testing the DQ* Disks(read only)
Testing the DF* Disks(read only)
No MK* Tapes available for testing
No MU* Tapes available for testing
Testing the DV* Floppy Disks(read only)
Testing the VGA (Alphanumeric Mode only)
Testing the EWA0 Network
Testing the EWB0 Network
P00>>>
The test command also does a quick test on the system speaker. A beep is
emitted as the command starts to run.
The tests are run sequentially, and the status of each subsystem test is
displayed to the console terminal as the tests progress. If a particular device is
not available to test, a message is displayed. The test script does no destructive
testing; that is, it does not write to disk drives.
The syntax is:
test [argument]
Use the -lb (loopback) argument for console loopback tests.
To run a complete diagnostic test using the test command, the system
configuration must include:
•
A serial loopback connected to the COM2 port (not included)
• A parallel loopback connected to the parallel port (not included)
- AlphaServer ES40 1
- Contents 5
- Chapter 6 Updating Firmware 7
- Chapter 7 Troubleshooting 7
- Chapter 8 Specifications 7
- Examples 9
- Intended Audience 11
- Document Structure 11
- Documentation Titles 12
- Support Resources 12
- Chapter 1 13
- System Overview 13
- System Enclosures 14
- System Chassis—Rear View 17
- Rear Ports and Slots 18
- 2 3 4 5 6 20
- System Board 22
- PCI Backplane 24
- Table 1–1 PCI Slot Mapping 25
- ➋ +5 V Auxiliary 27
- Removable Media Storage 28
- Hard Disk Storage 29
- Pedestal 30
- Pedestal/Rack 32
- Chapter 2 33
- Operation 33
- Powering Up the System 34
- Power-Up Displays 35
- P00>>> 40
- AlphaServer 43
- System Consoles 44
- Configuration 50
- Example 2–6 Show Boot* 51
- Example 2–7 Show Config 52
- TOSHIBA CD-ROM XM-6302B 54
- Example 2–8 Show Device 57
- Example 2–9 Show Memory 58
- Setting SRM Console Security 60
- Operation 2-31 63
- =Express ESC=Exit 64
- Setting Automatic Booting 67
- Chapter 3 77
- Booting and Installing 77
- 3.1.1 bootdef_dev 78
- 3.1.2 boot_file 79
- 3.1.3 boot_osflags 80
- Booting Tru64 UNIX 84
- Example 3–2 RIS Boot 86
- ➌ sets the internal Internet 87
- Booting OpenVMS 90
- Example 3–5 InfoServer Boot 92
- Chapter 4 103
- Using the Remote 103
- Management Console 103
- RMC Overview 104
- Operating Modes 106
- 4.2.1 Bypass Modes 108
- Terminal Setup 111
- Entering the RMC 112
- RMC Command-Line Interface 115
- RMC> set com1_mode 117
- Field Meaning 119
- Troubleshooting Tips 132
- Chapter 5 135
- Configuring and Installing 135
- Components 135
- Removing Enclosure Panels 136
- ➊. Slide 137
- V @ >240VA 140
- Hot-Plug Components 143
- 00111222 144
- Installing a Hard Drive 148
- Non-Hot-Plug Components 150
- CPU Configuration 152
- Installing CPUs 154
- Memory Configuration 157
- Installing DIMMs 160
- ➌ on the MMB slot 163
- PCI Configuration 164
- 10-Slot System 165
- 6-Slot System 165
- Installing PCI Cards 166
- Installing a Second Disk Cage 172
- Install the SCSI controller 173
- External SCSI Expansion 175
- Chapter 6 177
- Updating Firmware 177
- Sources of Firmware Updates 178
- Firmware Update Utility 180
- Manual Updates 182
- Updating from the CD-ROM 183
- Run new AlphaBIOS 188
- Chapter 7 191
- Troubleshooting 191
- Power-Up Error Messages 192
- 7.1.3 No MEM Error 196
- RMC Error Messages 198
- SROM Error Messages 200
- SRM Diagnostics 202
- 7.4.2 Show Device Command 203
- Example 7–4 Test Command 204
- 7.4.4 Show FRU Command 206
- ➊ ➋➌ ➍ ➎ ➏ 206
- Troubleshooting 7-17 207
- FRUs with 207
- Continued on next page 207
- 7.4.5 Show Error Command 209
- 7.4.6 Show Power Command 210
- Troubleshooting 7-21 211
- Example 7–8 Crash Command 212
- Troubleshooting Tables 214
- Table 7–5 Power Problems 215
- Table 7–8 Boot Problems 218
- Option Card Problems 220
- Chapter 8 225
- Specifications 225
- Physical Specifications 226
- Operating 227
- H9A10 M-Series 229
- H9A15 M-Series 229
- Environmental Specifications 230
- Electrical Specifications 231
- Regulatory Approvals 232
- Acoustical Data 233
Produits connexes et manuels pour Serveurs Compaq AlphaServer ES40
Serveurs Compaq ProSignia 500 Spécifications
(23 pages)
(23 pages)
Serveurs Compaq 370 Guide d'installation
(186 pages)
(186 pages)
Serveurs Compaq ProLiant SL165s Spécifications
(117 pages)
(117 pages)
Serveurs Compaq ProLiant DL388p Spécifications
(106 pages)
(106 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.765 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels