Compaq ProLiant DL388e Guide de l'utilisateur Page 50
- Page / 127
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hardware options installation 50
• Observe the general DIMM slot population guidelines (on page 49).
• DIMMs may be installed individually.
Single-processor Advanced ECC population order
For Advanced ECC mode configurations with a single processor, populate the DIMM slots in the following
order:
• RDIMM: Sequentially in alphabetical order (A through I)
• UDIMM: A through F, sequentially in alphabetical order. Do not populate DIMM slots G through I.
Multi-processor Advanced ECC population order
For Advanced ECC mode configurations with multiple processors, populate the DIMM slots for each
processor in the following order:
• RDIMM: Sequentially in alphabetical order (A through I)
• UDIMM: A through F, sequentially in alphabetical order. Do not populate DIMM slots G through I.
Lockstep Memory population guidelines
For Lockstep memory mode configurations, observe the following guidelines:
• Observe the general DIMM slot population guidelines (on page 49).
• Always install DIMMs in channels 1 and 2 for each installed processor.
• Do not install DIMMs in channel 3 for any processor.
• DIMM configuration on channel 1 and channel 2 of a processor must be identical.
• In multi-processor configurations, each processor must have a valid Lockstep Memory configuration.
• In multi-processor configurations, each processor may have a different valid Lockstep Memory
configuration.
Single-processor Lockstep population order
For Lockstep memory mode configurations with a single processor, populate the DIMM slots in the following
order:
• RDIMM
o First: A and B
o Next: D and E
o Last: G and H
o Do not populate slots C, F, or I.
• UDIMM
o First: A and B
o Last: D and E
o Do not populate slots C, F, G, H, or I.
After installing the DIMMs, use RBSU to configure the system for Lockstep memory support ("Configuring
lockstep memory" on page 75).
- HP ProLiant DL388 G7 Server 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Systems Insight Display LEDs 9
- Rear panel components 11
- Rear panel LEDs and buttons 12
- System board components 14
- System maintenance switch 15
- NMI functionality 15
- DIMM slot locations 16
- SAS and SATA device numbers 17
- SAS and SATA hard drive LEDs 18
- PCI riser cage LEDs 19
- FBWC module LEDs 20
- Battery pack LEDs 21
- Hot-plug fans 22
- Component identification 23 23
- Operations 24
- Remove the access panel 25
- Install the access panel 26
- Remove the PCI riser cage 29
- Install the PCI riser cage 29
- Remove the air baffle 31
- Rack planning resources 32
- Optimum environment 33
- Temperature requirements 34
- Power requirements 34
- Rack warnings 35
- Installing hardware options 35
- Setup 37 37
- Registering the server 38
- Introduction 39
- Processor option 39
- Install the heatsink 44
- Memory options 46
- DIMM identification 47
- Memory configurations 47
- Installing a DIMM 53
- Optical drive option 57
- Expansion board options 60
- PCI riser board option 63
- Hard drive cage option 64
- Cabling 69
- BBWC battery cabling 70
- FBWC battery cabling 70
- Configuration and utilities 71
- HP ROM-Based Setup Utility 72
- Boot options 73
- BIOS Serial Console 73
- Configuring AMP modes 73
- Configuring mirrored memory 74
- Array Configuration Utility 75
- Management tools 76
- ROMPaq utility 77
- Erase Utility 77
- Redundant ROM support 78
- Diagnostic tools 79
- Keeping the system current 80
- Version control 81
- ProLiant Support Packs 81
- Firmware 82
- HP Smart Update Manager 82
- Care Pack 83
- Troubleshooting 84
- Symbols on equipment 85
- Warnings 85
- Symptom information 86
- Troubleshooting 87 87
- Loose connections 88
- Service notifications 88
- Server health LEDs 88
- Troubleshooting flowcharts 88
- Start diagnosis flowchart 89
- General diagnosis flowchart 90
- Symptoms: 92
- POST problems flowchart 94
- OS boot problems flowchart 96
- • Corrupted OS 97
- • Redundancy failure 99
- (http://www.hp.com/support) 100
- Troubleshooting 101 101
- Battery replacement 102
- FCC rating label 103
- Class A equipment 103
- Class B equipment 103
- Modifications 104
- • EMC Directive 2004/108/EC 105
- Japanese notice 106
- BSMI notice 106
- Korean notice 106
- Chinese notice 107
- Laser compliance 107
- Battery replacement notice 107
- Electrostatic discharge 109
- Specifications 110
- Technical support 113
- Technical support 114 114
- Customer Self Repair 115
- Technical support 116 116
- Reparo feito pelo cliente 117
- Technical support 118 118
- Technical support 119 119
- Technical support 120 120
- Acronyms and abbreviations 121
- Index 124 124
- Index 125 125
- Index 126 126
- Index 127 127
Produits connexes et manuels pour Serveurs Compaq ProLiant DL388e
(322 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.159 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels