Compaq External RAID Controller & Subsystem Manuel d'utilisateur Page 233
- Page / 347
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Infortrend10-20
10.3.1 Via Front Panel Keypad
Redundant Configuration Using Automatic Setting
Power-on Controller 1. Make sure Controller 2 is powered-off.
1. Enable Redundant Controller
Press [ENT] for two seconds on the front panel of
controller 1 to enter the main menu. Use ▼ or ▲
to navigate through the menus. Choose "View
and Edit Peripheral Dev.. (View and Edit
Peripheral Devices)," then press [ENT].
Choose "Set Peripheral Devices Entry," then press
[ENT].
Choose "Redundant Ctlr Function__", and then
press [ENT]. (Note: The current setting will be
displayed on the LCD) If this controller has never
been set as a redundant controller before, the
default setting of the redundant controller
function is "Disabled." The message "Redundant
Ctlr Function Disable" will be displayed on the
LCD. Press [ENT] to proceed.
Autoconfig.
The message "Enable Redundant Ctlr: Autocfg?"
will appear. Use ▼ or ▲ to scroll through the
available options ("Primary," "Secondary," or
"Autocfg"), then press [ENT] for two seconds to
select "Autocfg."
For the other controller is currently not
connected, status will be indicated as “Inactive.”
Once set, press [ESC] for several times to return
to the main menu.
2. Controller Unique ID
Enter “View and Edit Config Parms”->
“Controller Parameters”. Use ▼ or ▲ to find
“Ctlr Unique ID- xxxxx”.
This value will be used to generate a controller-
unique WWN node name and port names and to
identify the controller during the failover process.
Enter a hex number from 0 to FFFFF and press
[ENTER]. The value you enter should be
different for each controller.
View and Edit
Peripheral Dev
Set Peripheral
Devices Entry
Redundant Ctlr
Function Disable
Enable Redundant
Ctlr: Autocfg ?
Ctlr Unique
ID- 00012 ?
Redundant Ctlr:
Autocfg Inactive
View and Edit
Config Parms
Controller
Parameters ..
- Infortrend 1
- Generic Operation Manual 1
- Asia Pacific 2
- Americas 2
- Printed in Taiwan 3
- Table of Contents 4
- Chapter 7 Terminal Operation 7
- Chapter 8 Fibre Operation 8
- Chapter 12 Array Expansion 11
- Appendix D Event Messages 12
- Functional Table of Contents 13
- Chapter 8 Fibre Operation 15
- Chapter 12 Array Expansion 16
- Upgrading Firmware 17
- List of Tables 18
- List of Figures 18
- About This Manual 20
- Revision History: 21
- RAID Functions: 23
- An Introduction 23
- 1.3 RAID Levels 24
- Figure 1 - 2 NRAID 25
- Figure 1 - 3 JBOD 25
- RAID (0+1) 26
- 1.4 Spare Drives 28
- A Local Spare always has 29
- Global Spare 29
- 1.5 Identifying Drives 30
- 1.6 Rebuild 31
- 2. Manual Rebuild 32
- What is a logical volume? 34
- RAID 5 Logical Drive 35
- 24 drives, 1 redundancy drive 35
- Logical Volume 36
- 24 drives, 4 redundancy drive 36
- Multi-level RAID systems 39
- RAID (3+0) 39
- RAID (5+0) 39
- RAID Planning 40
- Optimization Mode 42
- 7. What RAID level? 42
- 8. Any spare drives? 43
- 9. Limitations? 43
- Configuring the Array: 44
- 2.3 Operation Theory 46
- 2.4 Tunable Parameters 49
- Accessing the Array 52
- Ethernet 52
- 3.2 Out-of-Band via Ethernet 55
- Other Concerns 56
- Requirements 56
- 5. Starting the Manager: 59
- 3.2.3 NPC Onboard 60
- The SNMP_TRAP section 61
- The EMAIL section 61
- The BROADCAST section 61
- LCD Screen Messages 62
- 4.3 Logical Drive Status 63
- 4.4 Logical Volume Status 64
- 4.5 SCSI Drive Status 65
- CH0=Host = 66
- 4.8 Cache Dirty Percentage 68
- 4.9 View and Edit Event Logs 68
- LCD Keypad Operation 69
- 5.3 View Connected Drives: 73
- 5.4 Creating a Logical Drive 74
- Spare Drive Assignments: 75
- Disk Reserved Space: 75
- Write Policy: 75
- Initialization Mode: 75
- Stripe Size: 76
- Beginning Initialization 76
- 5.5 Creating a Logical Volume 78
- Logical Volume Assignment 79
- Drive to Host LUN 81
- Adding a Global Spare Drive 83
- Rebuild Settings 83
- Scanning New SCSI Drive 91
- Identifying a Drive 92
- Viewing IDs 94
- Adding a Channel ID 94
- Deleting a Channel ID 95
- Setting Transfer Speed 97
- Setting Transfer Width 98
- Parity Check 100
- Disconnecting Support 100
- Maximum Tag Count 100
- IMPORTANT! 101
- Restore to Default Setting 101
- 5.13 System Functions 102
- Reset Controller 103
- Shutdown Controller 103
- Disabling Password 103
- Controller Maintenance 104
- Saving NVRAM to Disks 104
- Restore NVRAM from Disks 104
- 5.14 Controller Parameters 105
- Controller Date and Time 106
- Time Zone 106
- Date and Time 107
- 5.15 SCSI Drive Utilities 108
- SCSI Drive Read/Write Test 109
- Terminal Screen Messages 110
- 6.2 Main Menu 111
- 6.3 Quick Installation 111
- 6.4 Logical Drive Status 113
- 6.5 Logical Volume Status 114
- 6.6 SCSI Drive Status 115
- 6.7 SCSI Channel’s Status 116
- CurSynClk 117
- Terminal Operation 120
- Limitations: 121
- 7.4 Creating a Logical Drive 124
- Choosing a RAID Level: 125
- Choosing Member Drives: 125
- Logical Drive Preferences: 125
- Maximum Drive Capacity: 125
- Assign Spare Drives: 126
- Disk Reserved Space 126
- Logical Drive Assignments: 126
- Write Policy 126
- Initialization Mode 127
- Stripe Size 127
- 7.5 Creating a Logical Volume 129
- WARNING! 131
- Settings 134
- Drive Members 135
- Partition 1 136
- Rebuilding a Logical Drive 137
- Media Scan 138
- Edit Host-ID/WWN Name List 140
- Pass-through SCSI Commands 140
- Scanning New Drive 141
- Slot Number 142
- Drive Entry 142
- Identifying Drive 142
- Redefining Channel Mode 144
- Viewing and Editing SCSI IDs 145
- Deleting an ID 146
- Setting Channel Terminator 147
- Setting a Transfer Speed 147
- Setting the Transfer Width 148
- Maximum Transfer Width 150
- Data Rate 151
- 7.13 System Functions 153
- Changing the Password 154
- Setting a New Password 154
- Disabling the Password 155
- 7.14 Controller Parameters 156
- Password Validation Timeout 158
- Controller Unique Identifier 158
- Set Controller Date and Time 160
- 7.15 Drive Information 161
- SCSI Drive Low-level Format 162
- Fibre Operation 164
- 8.2 Major Concerns 165
- 8.3 Supported Features 167
- Drive IDs: 168
- Parameters 169
- (RCC Channel): 170
- View Channel WWN 170
- View and Edit Fibre Drive 171
- View Drive Information 172
- 2. Drive-Side Dual Loop: 173
- Filtering 177
- Creating LUN Masks 178
- WWN Name List 179
- Sample Configuration: 183
- Configuration Procedure: 184
- Advanced Configurations 186
- 9.1.1 Clone Failing Drive: 187
- Perpetual Clone: 188
- A. Introduction 190
- Disable: 191
- Detect Only: 191
- Clone + Replace: 191
- Configuration Procedure 192
- Using S.M.A.R.T. Functions 193
- Connection: 197
- Maximum Queued I/O Count: 198
- LUNs per Host SCSI ID 198
- LUN Applicability: 198
- Peripheral Device Type: 199
- In-band (SCSI or Fibre): 199
- Operating Systems: 200
- 9.2.2 Drive-side Parameters: 203
- SCSI Motor Spin-Up 203
- SCSI Reset at Power-Up 204
- Disk Access Delay Time 205
- SCSI I/O Timeout 205
- Periodic Drive Check Time 207
- Idle Drive Failure Detection 208
- Dynamic Switch Write-Policy 210
- 9.4 Disk Array Parameters 212
- Verification on Writes 213
- Redundant Controller 214
- 10.1.1 Setup Flowchart 215
- Connection 215
- Fibre-Based Controllers 216
- Primary and Secondary IDs 219
- 10.1.4 Fault-Tolerance 221
- A.Channel Bus 222
- Replacing a Failed Unit: 224
- Auto-Failback: 224
- E. Controller Failure 226
- 10.2 Preparing Controllers 227
- Controller Settings: 228
- 10.2.2 Limitations 229
- Cache Synchronization 230
- Battery Support 230
- Infortrend10-18 231
- 10.3 Configuration 232
- 10.3.1 Via Front Panel Keypad 233
- 2. Controller Unique ID 234
- Drive Channel 235
- Controller 236
- Secondary 238
- Controller Replaced? 244
- Channel) 247
- Secondary Controller RS-232 247
- Remote Redundant Controller 247
- Record of Settings 248
- Partition Information 249
- Logical Volume Information 250
- 11.3 View and Edit Host LUN’s 251
- Host Filter Entries 252
- Caching Parameters 256
- Host Side SCSI Parameters 256
- Drive Side SCSI Parameters 256
- 11.9 RAID Security: Password 259
- Array Expansion 260
- Note on Expansion 261
- 12.2 Mode 1 Expansion: 263
- 12.3 Mode 2 Expansion: 266
- Larger Capacity 266
- Expand Logical Drive 268
- 12.5 Expand Logical Volume 270
- Volume Extension in 271
- Windows 2000 271
- LCD Keypad Navigation Map 277
- View & Edit 278
- Navigation Map 279
- Firmware Functionality 284
- Specifications 284
- Advanced Features: 285
- Caching Operation: 286
- RAID Expansion: 287
- Fibre Channel Support: 288
- S.M.A.R.T. Support: 289
- Redundant Controller: 289
- Data Safety: 290
- System Security: 291
- Environment Management: 292
- User Interface: 293
- Remote Manageability: 293
- JBOD-Specific: 294
- System Functions: 295
- RAIDWatch Manager 296
- Emulation 298
- Event Messages 301
- Logical Drive Event 303
- General Target Events 303
- Controller Event 307
- Logical Drive Event: 317
- General Target Events: 322
- IndexIndex 340
Produits connexes et manuels pour Logiciel Compaq External RAID Controller & Subsystem
Logiciel Compaq AA-PWCBD-TE Manuel d'utilisateur
(152 pages)
(152 pages)
(71 pages)LG MH-7046SQZ manuals
Owner’s manuals and user’s guides for Microwaves LG MH-7046SQZ.
We providing 1 pdf manuals LG MH-7046SQZ for download free by document types: User Manual
Table of contents
Contents
3
Two stage
10
ﻊﻳﺮﺳ ﻞﻴﻐﺸﺗ
11
Combination
13
Auto cook
20
More or Less
21
Utensils
26
Questions &
29
MH-7046SQ
31
MH-7046SQZ
31
‚öž≈‚öž≈
37
WUDÐ a³D«
38
WUÞ Èu²
39
ZK¦« WЫ–≈
46
XR*«XR*«
50
WK¾Ý√WK¾Ý√
59
More products and manuals for Microwaves LG
| Models | Document Type |
|---|---|
| MB-3822ES |
User Manual
LG MB-3822ES Owner's manual,
18 pages
|
| MH-6644B |
User Manual
LG MH-6644B Owner’s Manual,
34 pages
|
| MS2327B |
User Manual
LG MS2327B Owner’s Manual,
16 pages
|
| MS-3446VR |
User Manual
LG MS-3446VR Owner’s Manual,
33 pages
|
| MS-543XD |
User Manual
LG MS-543XD Owner’s Manual,
20 pages
|
| MS2021C |
User Manual
LG MS2021C Owner’s Manual,
17 pages
|
| MS-2344BS |
User Manual
LG MS-2344B Owner’s Manual [en] ,
32 pages
|
| MH-7246SQZ |
User Manual
LG MH-7246SQZ Owner’s Manual,
28 pages
|
| MS-272W |
User Manual
LG MS-272W Owner’s Manual,
14 pages
|
| MS2647MS |
User Manual
LG MS2647MB Owner’s Manual,
32 pages
|
| MH5947US |
User Manual
LG MH5947US Owner’s Manual,
26 pages
|
| MC-805CLR |
User Manual
LG MC-805CLR Owner’s Manual,
32 pages
|
| MS-5645KR |
User Manual
LG MS-5645KR Owner’s Manual,
24 pages
|
| MS-2027C |
User Manual
LG MS-2027C Owner’s Manual,
17 pages
|
| MS2843GARS |
User Manual
LG MS2843GARS Owner’s Manual,
37 pages
|
| MS-2023J |
User Manual
LG MS-2023J Owner’s Manual,
15 pages
|
| MS4082X |
User Manual
LG MS4082X Owner’s Manual,
37 pages
|
| MJ3281BP |
User Manual
LG MJ3281BP Owner’s Manual,
36 pages
|
| MH-6347DR |
User Manual
LG MH-6347DR Owner’s Manual,
33 pages
|
| MG-7243J |
User Manual
LG MG-7243J Owner’s Manual,
34 pages
|
© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels